Page 1
| Requirement | From |
|---|---|
| A certificate of product liability insurance, often $1 million or more, naming the buyer | Buyer packet and the distributor's own vendor terms, which will give the exact figure. Illustrative. |
| Status | ||
|---|---|---|
| Legal name | Not formed yet | not yet |
| Entity | Planned: single-owner LLC | not yet |
| Product liability insurance | Quotes requested | in progress |
| Rules that apply | To check: EPA rules for pest-control devices | in progress |
| Years in business | 0 | ready |
| Owner | The inventor: product idea, CAD and prototypes so far | ready |
Page 2
A molded nylon base carries the bait cup, a finger guard and the spring post in one part. A molded trigger plate with a bait spike pivots on the base. The classic wire bail, music-wire spring and steel staple are kept. The trap is set from the side, with a molded mark showing where the hand goes, so no finger is in the bail's path.
Barns, garages and homes; sold through hardware and farm-supply stores
To hardware and farm-supply distributors, who sell to stores. No direct sales to consumers (project charter, scope).
| Part no. | Part | What it is | Make or buy | Supplier |
|---|---|---|---|---|
| MT-001 | Plastic base | Nylon 6/6 base with the bait cup, finger guard and spring post molded in. Wall 1.8 mm, draft 1 degree. | make | Molder, to quote |
| MT-002 | Trigger plate | Nylon 6/6 pedal with the bait spike molded on. Its own small mold. | make | Molder, to quote |
| MT-003 | Wire bail | Music wire kill bar, the classic shape. Purchased. | buy | Wire-form supplier, to quote |
| MT-004 | Spring | Music wire torsion spring, classic size. Purchased. | buy | Spring maker, to confirm (A-002) |
| MT-005 | Staple | Steel staple that holds the spring to the base. Pressed in at assembly. | buy | Fastener distributor |
| MT-900 | Assembly | Hand assembly, 12 seconds, staple pressed in. | make | In house |
| MT-950 | Packaging | Card and blister for one trap. | buy | Packaging supplier, to quote |
A warning label on the card, and a molded set-from-the-side mark on the base (risk table F8 and F11). The label text is not written yet.
Page 3
From the product's risk analysis: the ways it could fail that could hurt someone, what was done about each, and the severity before and after (1 to 10).
| Failure | Effect | What was done | Severity | Status | |
|---|---|---|---|---|---|
| F1 | Base cracks at the spring seat | As proposed, the trap fails. A user can be hurt. | Add a short rib at the spring seat; Use an engineered resin | 8 → 6 | accepted |
| F11 | A finger stays in the path of the bail while setting | As proposed, someone can be hurt. | Mold a set-from-the-side mark; Mold a finger guard beside the bail | 9 → 5 | accepted |
| Requirement | Source | Source status | Met? | |
|---|---|---|---|---|
| R-001 | Landed cost at or under the distributor's target | Project charter | inventor said | not met |
| R-002 | Can be set without a finger in the bail's path | Project charter | inventor said | not checked yet |
| R-003 | Nylon base and trigger keep their fit when damp | Project charter | inventor said | not checked yet |
| R-004 | If a snap trap is a pesticide device, its label carries the making plant's EPA establishment number and no false claims | EPA pesticide devices: 40 CFR 152.500 and 40 CFR 156.10(f), via EPA Pesticide Registration Manual chapter 13 (www.epa.gov) | from a summary | not checked yet |
| R-005 | Moisture uptake and the change in size when damp | Resin maker's datasheet for the chosen nylon 6/6 grade | to find | not checked yet |
Recall and incident search not run yet (library: cpsc-recalls, saferproducts).
None. New business.
Page 4
| Question | What the record shows |
|---|---|
| Does a policy cover a product made by a molder and assembled at home? | Molded by Molder A (to quote); assembled by hand in house (cost sheet MT-900). |
| What limits and deductible fit a product this size, and what would it cost? | Planned first-year sales are on page 1. |
| Can it start under the inventor and move to the LLC when it is formed? | No company yet (company record). |
| What would you need to see about the risks? | Page 3: the risk analysis and the requirements, with their sources. |
| Does a homeowner's policy cover any of this? | The trap is assembled at home. Ask; don't assume. |
| When does it have to be in place? | Before the first shipment, planned for April 30, 2027, and before any buyer asks for the certificate. |
These are questions, not assumptions about coverage. What a policy covers is in the policy itself: ask for the policy wording, not only the quote.
Last page
Know what product liability coverage would cost, and what it takes, before a buyer asks for the certificate
Don't buy a policy in the room. Get the policy wording and two or three quotes, then compare.
| Question | Answer |
|---|---|
| What are your annual sales? | None yet. The plan is on page 1. |
| Any claims? | None. New business. |
| Who makes it? | Page 2. |
| Today | Note | |
|---|---|---|
| Legal name | Not formed yet | Forming a single-owner LLC is with the Office Manager Bot (business risk B5). |
| Entity | Planned: single-owner LLC | |
| Tax ID (EIN) | Not yet | Needed for a W-9 and a business bank account. Free from the IRS once the LLC exists. |
| W-9 for vendor setup | After the tax ID | |
| Business bank account | Not yet | |
| Product liability insurance | Quotes requested | Buyers often ask for a certificate of $1 million or more naming them. Illustrative. |
| UPC / GTIN barcodes | Not yet | License from GS1 before packaging is printed. Illustrative. |
| Rules that apply | To check: EPA rules for pest-control devices | A mechanical trap is a pest-control device; check EPA labeling and establishment rules before the first shipment. Illustrative. |
Pages 1 to 4. Not this prep sheet.
Record what was said in this folder; add any signal to market-evidence.csv; update contacts.csv with the next step and date; put every promise on the action log (sop-meeting-prep.txt step 8).